February 9, 2022 NHTSA CAMPAIGN NUMBER: 22V069000
Seat Belt Pretensioner May Explode
An exploding seat belt pretensioner can project metal fragments into the vehicle, striking vehicle occupants and resulting in injury.
NHTSA Campaign Number: 22V069
Manufacturer Hyundai
Motor America
Components SEAT BELTS
Potential Number of Units Affected 354
Summary
Hyundai
Motor America (Hyundai
) is recalling certain 2020-2021 Accent vehicles. In the event of a crash, the front driver-side and/or passenger-side seat belt pretensioner(s) may explode upon deployment.
Remedy
Dealers will replace the seat belt pretensioners, free of charge. Owner notification letters were mailed February 24, 2022. Owners may contact Hyundai
customer service at 1-855-371-9460. Hyundai
’s number for this recall is 219. This recall is an expansion of NHTSA recall number 21V-796. This recall is replaced by NHTSA recall number 22V-354. Vehicles already repaired under this recall will need to have the new remedy completed.
Notes
Owners may also contact the National Highway Traffic Safety Administration Vehicle Safety Hotline at 1-888-327-4236 (TTY 1-800-424-9153), or go to www.nhtsa.gov.
Check if your Hyundai has a Recall
FRONT SEAT BELT PRETENSIONER REPLACEMENT (RECALL 219)
Description: The front seat pretensioner may deploy abnormally in the vehicles described below, causing the MGG (Micro Gas Generator) to detach from the assembly. This bulletin describes the procedure to replace the front seatbelt pretensioner to resolve the condition.
Applicable Vehicles:
Certain 2020-2021MY Accent (HC) vehicles produced from 3/25/2020 to 7/29/2020.
Parts Information:
| MODEL | PART NAME | PART NUMBER | NOTES |
| Accent (HC) | Front Seatbelt Pretensioner | 88810-J0600QQH | Only Replace LH Side |
| Trim Fastener | 82315-2W000 | 4 Needed |
Refer to the QR code or link below for guided video information:
Hyundai Service Learning – Recall 219 Service Procedure
Service Procedure:
1. Move the front seat as far forward as possible.
NOTICE
Accent vehicles are equipped with manual levers to adjust seat position.
2. Record radio presets and turn off the vehicle’s ignition key before continuing.
3. Disconnect the negative (-) battery terminal.
4. Partially remove the front door body side weather strip (C).
5. Remove the front door scuff trim (D) using a flat head screwdriver or plastic trim remover.
NOTICE
If using a screwdriver, be sure to wrap protective tape around the tip to prevent damage on the trim and panels.
6. Partially remove the rear door body side weather strip (E).
7. Partially remove the rear door scuff (F) using a screwdriver or plastic trim remover.
8. Move the front seat belt lower anchor cover (G) upward.
9. Loosen the mounting bolt (H) and remove the front seat belt lower anchor.
NOTICE
Tightening Torque:
28.9-39.8 lb ft (39.2 53.9 Nm)
10. Pull and remove the center pillar lower trim (I).
NOTICE
Replace existing fasteners with new ones.
11. Remove the center pillar upper trim (J).
12. Loosen the front seat belt upper anchor mounting bolt (K) and remove the front seat belt anchor.
NOTICE
Tightening Torque:
28.9-39.8 lb ft (39.2 53.9 Nm)
13. Loosen the mounting bolts (L) and (M) and remove the front seat belt pretensioner.
NOTICE
Tightening Torque:
L: 5.8-8.7 lb ft (7.7 11.8 Nm)
M: 28.9-39.8 lb ft (39.2 53.9 Nm)
14. Press in the tabs for the locking pin (N) to disconnect the front seatbelt pretensioner connector (O) and the free active seatbelt connector (P).
15. Remove the front seat belt pretensioner.
16. Install the newly supplied front seat belt pretensioner.
17. Reinstall parts in reverse order of removal. Make sure you replace existing fasteners with new ones.
NOTICE
Move the height adjuster lever (Q) to the highest point before reinstalling the upper center pillar trim.
18. After connecting the negative (-) battery terminal, be sure to reprogram radio presets.
19. The service procedure is complete.
RECALL 219 ATTACHMENT A
CHRONOLOGY OF EVENTS LEADING UP TO DEFECT DECISION
❖ September 2021
On September 15, 2021, NHTSA’s ODI informed HMA’s NASO of a crash incident involving a model year 2021 Hyundai
Elantra vehicle where the driver-side seat belt pretensioner allegedly deployed abnormally causing metal fragments to enter the rear cabin and resulting in injury to an occupant’s leg. NHTSA was notified of the incident by a law firm representing the operator of the incident vehicle. The law firm also notified HMA’s external counsel on the same day, who then alerted HMA’s Legal department of the incident.
In subsequent discussions with the agency following the initial notice, ODI requested Hyundai
’s assessment of the incident under cover of SGO 2015-01, a standing general order involving abnormal deployments of frontal airbag inflators manufactured by ARC. On September 22, 2021, in accordance with requirements set forth in SGO 2015-01, HMA submitted its first report notifying ODI of its receipt of the 2021 Elantra incident.
On September 30, 2021, NASO provided an update on its investigation of the 2021 Elantra incident.
NASO informed ODI of plans to inspect the incident vehicle on October 8, 2021. NASO also informed ODI that it would be targeting seat belt pretensioners produced in the same production lot as the incident pretensioner for further study into root cause and manufacturing/design defect identification.
On October 6, NASO convened its North American Safety Decision Authority. Although the cause of the abnormal deployment is unknown, NASO decided to conduct a safety recall of vehicles equipped with pretensioners produced within the same production lot to conduct a detailed part return analysis.
❖ December 2021
Hyundai
actively continued its investigation to determine if a specific root cause and defect trend exists. On December 3, 2021, HMC notified NASO of a second incident occurring on a 2020 Hyundai
Accent vehicle in Puerto Rico. According to supplier information, the incident pretensioner was produced thirteen months prior to the suspect production lot initially identified in Recall 211. In accordance with requirements set forth in SGO 2015-01, HMA submitted a report notifying ODI of the new incident on December 10, 2021.
Based on this information, on December 10, 2021, NASO re-convened its North America Safety Decision Authority and decided to expand Recall 211 to include model year 2020-2021 Hyundai
Accent vehicles equipped with pretensioners from the earlier suspect production lot. Hyundai
will continue to actively investigate this condition and conduct detailed part return analysis on both suspect production lots to determine if a specific root cause and defect trend exists.
❖ February 2022
On February 7, NHTSA’s ODI met with NASO to discuss tentative plans to require all manufacturers to submit new recall filings when expanding the vehicle scope of an existing recall that has been filed and posted to NHTSA’s recall website. ODI requested NASO to file a new recall for the model year 2020-2021 Hyundai
Accent vehicles previously specified in Hyundai
’s amendment of Recall 211 filed December 17, 2021. In an effort to enhance customer notifications and comply with ODI’s request, on February 8, 2022, NASO re-convened its North America Safety Decision Authority and decided to conduct a new recall of model year 2020-2021 Hyundai
Accent vehicles in the U.S. for the same defect specified in Recall 211.
As of the date of this filing, Hyundai
is aware of one (1) related injury from one (1) crash event(s) in the U.S. received on December 3, 2021.
2 Affected Products
Vehicle
| MAKE | MODEL | YEAR |
| HYUNDAI | ACCENT | 2020-2021 |
10 Associated Documents
Defect Notice 573 Report
RCLRPT-22V069-2730.PDF 213.416KB
Recall Acknowledgement
Attachment A – Chronology
RMISC-22V069-9202.pdf 89.009KB
Remedy Instructions and TSB
RCRIT-22V069-7370.pdf 756.193KB
ISSUED Owner Notification Letter(Part 577)
RCONL-22V069-3505.pdf 179.649KB
Recall 573 Report – March 4, 2022
RCLRPT-22V069-7374.PDF 213.631KB
Recall Quarterly Report #1, 2022-1
RCLQRT-22V069-8748.PDF 211.132KB
Recall Quarterly Report #2, 2022-2
RCLQRT-22V069-0006.PDF 211.23KB
Recall Quarterly Report #3, 2022-3
RCLQRT-22V069-3314.PDF 211.31KB
Recall Quarterly Report #4, 2022-4
RCLQRT-22V069-5957.PDF 211.421KB
Latest Recalls Documents
- [Easy to Use—Work Out of the Box] + [FOXWELL 2026 New Version] FOXWELL NT604 Elite scan tool is the 2026 new version from FOXWELL, designed for car owners who want to figure out the cause of issues before fixing car problems by scanning common systems like ABS, SRS, engine, and transmission. The NT604 Elite obd2 scanner diagnostic tool comes with the latest software—no need to waste time downloading software first. Plug the scanner into the OBDII port with OBDII cable to start the diagnosis.
- [Affordable] + [Reliable Car Health Monitor] Will you be confused what happens when the warning light of ABS/SRS/transmission/check engine flashes? Instead of taking your cars to dealership, this FOXWELL scanner will help you do a thorough scanning and detection for your cars and pinpoint the root cause. Note:The device is a diagnostic tool, not a repair tool. To turn off a warning light, you must first physically repair the issue causing it. Only then can the scanner be used to clear the corresponding fault code.
- [5 in 1 Car Diagnostic Scanner] Compared with obd scanners (50-100), NT604 Elite code scanner not only includes their OBDII diagnosis but also serves as ABS/SRS scanner, transmission and check engine code reader. When it’s an odb2 scanner, you can use it to check if your car is ready for annual test through I/M readiness menu. In addition, live data stream, built-in DTC library, data play back and print, all these features are a big plus for it. Note: doesn't support maintenance functions like reset or relearn. For the SRS system, NT604 Elite can read and clear common fault codes not caused by a crash, but crash/collision data cannot be cleared.
- [Fantastic AUTOVIN] + [No extra software fee] Through the AUTOVIN menu, this NT604 Elite car scanner allows you to get your V-IN and vehicle info rapidly, no need to take time to find your V-IN and input one by one. What's more, the NT604 Elite ABS SRS scanner supports 60+ car brands from worldwide (America/Asia/Europe). You don’t need to pay extra software fee. AUTOVIN may not work on some older vehicles or certain vehicle brands. If AUTOVIN fails, please input the vin code manually or go to the Diagnostic Menu to select your vehicle model.
- [Solid protective case KO plastic carrying bag] + [Lifetime update] Almost all same price-level car scanner diagnostic tool only offers plastic bag to hold the scanner.However, NT604 Elite automotive scanner is equipped with solid protective case, preventing your obd2 scanner from damage. Then you don’t need to pay extra money to buy a solid toolbox.
- 【Reset ABS/SRS/Transmission/Engine Lights】 More than an check engine code reader, OBDMATE OM901 obd2 scanner performs comprehensive diagnostics for the 4 most-used systems (ABS/SRS/Engine/Transmission). It quickly clears fault codes, turns off warning lights, read data stream and auto VIN.
- 【3.5" Handheld Scanner with 4 System Diagnose】 3.5" Super large TFT screen equipped displays an intuitive menu and clear readings of various sensors from ABS, SRS, ECM and TCM systems. It arrived with a silicone protective case and hard-shell carrying case, ensuring long-lived durability and drop resistance. The car diagnostic tool is plug-to-play designed, plug it and get diagnosis started without any batteries or updates required.
- 【One-Click I/M Readines&Full OBD2 Functions】 Press F1 to get an intuitive corloured form about whether various emissions-related systems on the vehicle are operating properly. Help you get smog-check ready quickly. OM901 car scanner supports all essential OBD2 functions you need: read & clear codes, view freeze frame, read I/M readiness, retrieve VIN, live data stream (with graphing display), O2 sensor test, onboard monitoring mode, and EVAP leak test.
- 【Battery Voltage Check&DLC Pin Test】 It allows you to monitor battery health by testing current battery voltage. Plus, this obd2 diagnostic tool features DLC 16-PIN test to check current voltage of every pin.
- 【Automotive Scanner Diagnostic Kit】 The package comes with 1 car scanner, 1 USB-type c cable, 1 hard storage bag and 1 user manual(en). Free to update without any hidden fees. 5 languanges available in setting including English, French, Italian, German and Espanish. Valuable and Portable, making it a great tool kit for car owners, DIY enthusiasts, and professional mechanics.
- [Diagnose Like a Pro] BlueDriver Pro is a professional OBD2 scanner and diagnostic tool that helps you scan, understand, and clear vehicle trouble codes with confidence. Turn your phone into a powerful car diagnostic scanner—no guesswork, no unnecessary repairs.
- [Read and Clear More Codes Than Ever] Read and clear more codes than basic car code readers. Access enhanced diagnostics for Check Engine, ABS, SRS, Airbag, TPMS, Transmission.
- [Verified Fixes and Real-Time Data] Get unlimited, technician-verified repair reports matched to your VIN, with definitions, causes, and confirmed fixes. Monitor live vehicle data as you drive, view freeze frames, check smog readiness, and analyze Mode 6 test results.
- [Wireless & Bluetooth Enabled] - Say goodbye to wires. BlueDriver connects with Bluetooth via your phone/tablet to a sensor that plugs into your car's OBDII port. Get all of the capabilities of an expensive code reader & scan tool without any annoying wires.
- [Broad Make & Model Coverage] Strong support for GM, Ford, Stellantis (RAM, Jeep, Chrysler), Toyota, Honda, Nissan, Mazda, Subaru, Hyundai
, Mercedes-Benz, BMW, and VW.
- [All System Diagnostics, Professional-Level Scanner] - BLCKTEC 460T is the ultimate OBD2 diagnostic tool for home mechanics and professionals. It supports all 10 OBD2 modes, reads and clears Engine/Transmission/ABS/SRS codes, performs All-System Diagnostics, offers workshop reset tools, and provides real-time live data. It helps you pinpoint issues, assess your car's condition, and prepare for SMOG checks with ease. NOTE: Function availability depends on your vehicle. Before you buy, be sure to use the Compatibility Checker on BLCKTEC website or contact our customer support to verify that the features you need are supported for your vehicle’s specific year, make, and model.
- [12+ Most Popular Reset Functions] - BLCKTEC 460T OBD2 scanner offers 12+ dealer-level service functions, including Oil Maintenance Reset, ABS Bleeding, EPB Reset, SAS(Steering Angle Sensor) Recalibration, DPF(Diesel Particulate Filter) Reset, Throttle Body Relearn, Battery Reset/Initialization, TPMS Relearn, Transmission Reset, Fluid Change Reset, Maintenance Reset and more, enabling you to perform workshop services like a pro. NOTE: Function availability depends on your vehicle. Be sure to use the Compatibility Checker on BLCKTEC website to verify that the features you need are supported for your vehicle.
- [Real-Time OBD2 and OEM Live Data, Freeze Frame Data] - BLCKTEC 460T helps diagnose vehicle issues when warning lights like Check Engine Light or ABS/SRS Light appear. It offers detailed DTC info, ECU Freeze Frame Data, and real-time OBD2 and advanced OEM live data, including Engine, Transmission, ABS, SRS, and more, making it easy to diagnose and resolve vehicle problems. You can view, graph, record, replay, and overlay up to four live data streams in a single graph for better analysis.
- [AutoVIN, AutoReLink, AutoScan, 3X Faster] - Equipped with AutoVIN technology, 460T automatically retrieves the VIN to save you time. Its AutoScan and AutoReLink features scan all of the vehicle's ECUs and detect any fault codes immediately after you plug the scanner into the vehicle's OBD2 port - no button presses required. Additionally, it regathers DTC and I/M readiness information every 30 seconds, simplifying monitor tests. 460T's advanced technology makes it 3X faster than other products.
- [Get RepairSolutions2, the #1 Auto Repair App for Free] - When paired with RepairSolutions2(RS2) App, 460T becomes even more powerful. RS2's Verified Fix Database built by master technicians, provides the parts needed for the repair. Additionally, RS2 gives you access to OEM warranty info, maintenance schedules, TSB, and dealership recall info, making car care easier than ever. RS2 is free with no subscription fees and it stores your car scan reports in the cloud, allowing you to access, share, or print them anytime and anywhere.
- [Diagnose Like a Pro] BlueDriver Pro is a professional OBD2 scanner and diagnostic tool that helps you scan, understand, and clear vehicle trouble codes with confidence. Turn your phone into a powerful car diagnostic scanner—no guesswork, no unnecessary repairs.
- [Read and Clear More Codes Than Ever] Read and clear more codes than basic car code readers. Access enhanced diagnostics for Check Engine, ABS, SRS, Airbag, TPMS, Transmission.
- [Verified Fixes and Real-Time Data] Get unlimited, technician-verified repair reports matched to your VIN, with definitions, causes, and confirmed fixes. Monitor live vehicle data as you drive, view freeze frames, check smog readiness, and analyze Mode 6 test results.
- [Wireless & Bluetooth Enabled] - Say goodbye to wires. BlueDriver connects with Bluetooth via your phone/tablet to a sensor that plugs into your car's OBDII port. Get all of the capabilities of an expensive code reader & scan tool without any annoying wires.
- [Broad Make & Model Coverage] Strong support for GM, Ford, Stellantis (RAM, Jeep, Chrysler), Toyota, Honda, Nissan, Mazda, Subaru, Hyundai
, Mercedes-Benz, BMW, and VW.
SEOCONTENT-START
Technical Service Bulletin GROUP NUMBER RECALL 22-01-026H DATE MODEL(S) FEBRUARY 2022 Accent (HC) SUBJECT: FRONT SEAT BELT PRETENSIONER REPLACEMENT (RECALL 219) Description: The front seat pretensioner may deploy abnormally in the vehicles described below, causing the MGG (Micro Gas Generator) to detach from the assembly. This bulletin describes the procedure to replace the front seatbelt pretensioner to resolve the condition. Applicable Vehicles: Certain 2020-2021MY Accent (HC) vehicles produced from 3/25/2020 to 7/29/2020. As required by federal law, dealer s must not deliver new vehicle for sale or for lease to customers until all open recalls have been performed. Dealers must also perform all open recalls on used vehicles, demo, and rental vehicles prior to placing them into customer use and whenever an affe cted vehicle is in the shop for any maintenance or repair. When a vehicle arrives at the Service Department, access the “Vehicle Information” screen via WEBDCS to identify open Recalls. IMPORTANT FRONT SEAT BELT PRETENSIONER REPLACEMENT (RECALL 219) TSB #: 22-01-026H Page 2 of 7 SUBJECT: SUBJECT: Parts Information: MODEL PART NAME PART NUMBER NOTES Accent (HC) Front Seatbelt Pretensioner 88810-J0600QQH Only Replace LH Side Trim Fastener 82315-2W000 4 Needed Warranty Information: MODEL OP CODE OPERATION OP TIME CAUSAL PART NATURE CODE CAUSE CODE Accent (HC) 211M20R0 Front Seat Belt Pretensioner Replacement (LH ONLY) 0.4 M/H 88810-J0600QQH I11 ZZ3 NOTE 1: Submit Claim on Campaign Claim Entry Screen. NOTE 2: If a part that is not covered by this recall is in need of replacement while performing this recall, and the affected part is still under warranty, please submit a separate claim using the same repair order. If the affected part is out of warranty, submit a prior approval request for goodwill consideration prior to performing the work. NOTE 3: The incident part(s) may be subjected to callback through the Warranty Technical Center (WTC). Refer to the QR code or link below for guided video information: Hyundai
Service Learning – Recall 219 Service Procedure Service Procedure: 1. Move the front seat as far forward as possible. 2. Record radio presets and turn off the vehicle’s ignition key before continuing. 3. Disconnect the negative (-) battery terminal. Accent vehicles are equipped Accent vehicles are equipped with manual leverswith manual levers to adjust to adjust seat position.seat position. NOTICE NOTICE FRONT SEAT BELT PRETENSIONER REPLACEMENT (RECALL 219) TSB #: 22-01-026H Page 3 of 7 SUBJECT: SUBJECT: 4. Partially remove the front door body side weather strip (C). 5. Remove the front door scuff trim (D) using a flat head screwdriver or plastic trim remover. 6. Partially remove the rear door body side weather strip (E). C C D D If using a screwdriver, be sure If using a screwdriver, be sure to wrap protective tape to wrap protective tape around around the tip to prevent damage on the the tip to prevent damage on the trim and panels.trim and panels. NOTICE NOTICE E E FRONT SEAT BELT PRETENSIONER REPLACEMENT (RECALL 219) TSB #: 22-01-026H Page 4 of 7 SUBJECT: SUBJECT: 7. Partially remove the rear door scuff (F) using a screwdriver or plastic trim remover. 8. Move the front seat belt lower anchor cover (G) upward. 9. Loosen the mounting bolt (H) and remove the front seat belt lower anchor. F F G G H H Tightening Torque: Tightening Torque: 28.9 28.9 –– 39.8 lb39.8 lb–ft (39.2 ft (39.2 –– 53.9 Nm)53.9 Nm) NOTICE NOTICE FRONT SEAT BELT PRETENSIONER REPLACEMENT (RECALL 219) TSB #: 22-01-026H Page 5 of 7 SUBJECT: SUBJECT: 10. Pull and remove the center pillar lower trim (I). 11. Remove the center pillar upper trim (J). 12. Loosen the front seat belt upper anchor mounting bolt (K) and remove the front seat belt anchor. I I Replace existing fasteners with Replace existing fasteners with new ones.new ones. NOTICE NOTICE J J K K Tightening Torque: Tightening Torque: 28.9 28.9 –– 39.8 lb39.8 lb–ft (39.2 ft (39.2 –– 53.9 Nm)53.9 Nm) NOTICE NOTICE FRONT SEAT BELT PRETENSIONER REPLACEMENT (RECALL 219) TSB #: 22-01-026H Page 6 of 7 SUBJECT: SUBJECT: 13. Loosen the mounting bolts (L) and (M) and remove the front seat belt pretensioner. 14. Press in the tabs for the locking pin (N) to disconnect the front seatbelt pretensioner connector (O) and the free active seatbelt connector (P). 15. Remove the front seat belt pretensioner. 16. Install the newly supplied front seat belt pretensioner. L L M M Tightening Torque: Tightening Torque: L: 5.8 L: 5.8 –– 8.7 lb8.7 lb–ft (7.7 ft (7.7 –– 11.8 Nm)11.8 Nm) M: 28.9 M: 28.9 –– 39.8 lb39.8 lb–ft (39.2 ft (39.2 –– 53.9 Nm)53.9 Nm) NOTICE NOTICE O O P P N N FRONT SEAT BELT PRETENSIONER REPLACEMENT (RECALL 219) TSB #: 22-01-026H Page 7 of 7 SUBJECT: SUBJECT: 17. Reinstall parts in reverse order of removal. Make sure you replace existing fasteners with new ones. 18. After connecting the negative (-) battery terminal, be sure to reprogram radio presets. 19. The service procedure is complete. Move the height adjuster lever Move the height adjuster lever (Q) to the highest point before (Q) to the highest point before reinstalling the upper center reinstalling the upper center pillar trim.pillar trim. NOTICE NOTICE Q Q
**************************************************************************************************************
This notice applies to your Hyundai
, VIN: Dear This notice is sent to you in accordance with the National Traffic and Motor Vehicle Safety Act. Hyundai
has decided that a defect, which relates to motor vehicle safety, exists in your vehicle, with the VIN shown above. Hyundai
is initiating a safety recall to repair a condition involving the front seat belt pretensioners in certain 2020 – 2021 Accent vehicles in the U.S. and Canada. What is the problem? The front driver-side and/or passenger-side seat belt pretensioners in the subject vehicles were installed from a suspect production lot containing pyrotechnic-type pretensioners that may deploy abnormally and explode during a crash. At the time of this filing, the cause of the abnormal deployment is unknown. Hyundai
is recalling vehicles equipped with pretensioners produced within the same production lot and will conduct a detailed part return analysis. The part inspections and investigation will actively continue to determine if a specific root cause and defect trend exists. An abnormal pyrotechnic pretensioner deployment could cause the pretensioner to explode, and project metal fragments into the vehicle occupant compartment, which may result in injury to vehicle occupants. What will Hyundai
do? Your Hyundai
dealer will replace the Seat Belt Pretensioners. This procedure will be performed at NO CHARGE to you. What should you do? Please contact your nearest Hyundai
dealer to schedule the recall repair as soon as possible. The actual time required to perform the installation will take less than one hour, however your vehicle may be needed longer; therefore we recommend scheduling a service appointment to minimize inconvenience. If you have other questions If you require further assistance, you may contact the Hyundai
Customer Care Center at 1-855-371-9460. If you believe that the dealer and/or Hyundai
has failed or is unable to remedy the defect within a reasonable time, you may submit a complaint to the Administrator, National Highway Traffic Safety Administration, 1200 New Jersey Avenue S.E., Washington, D.C. 20590, or call the toll free Vehicle Safety Hot Line at 1-888-327-4236 (TTY: 1-800-424-9153), or go to https://www.safercar.gov. Thank you for your attention to this important safety matter. We apologize for any inconvenience this may have caused you. Hyundai
Motor America Hyundai
Motor America P.O. Box 20839 Fountain Valley, CA 92728-9937 IMPORTANT SAFETY RECALL 2020 – 2021 Accent Seat Belt Pretensioner Retiro del Mercado por Motivos de Seguridad — Si tiene preguntas llama 1-800-633-5151 y oprima “8” NHTSA Recall Number: 22V-069 Hyundai
Recall Number: 219 This is an important Safety Recall. • Please contact your nearest Hyundai
dealer to schedule the repair as soon as possible. • This repair will be performed at NO CHARGE to you. • For updated information, you can visit: www.HyundaiUSA.com/Campaign219
**************************************************************************************************************
OMB Control No.: 2127-0004 Part 573 Safety Recall Report 22V-069 The information contained in this report was submitted pursuant to 49 CFR §573 Manufacturer Name : Hyundai
Motor America Submission Date : MAR 04, 2022 NHTSA Recall No. : 22V-069 Manufacturer Recall No. : 219 Manufacturer Information : Manufacturer Name : Hyundai
Motor America Address : 10550 Talbert Avenue Fountain Valley CA 92708 Company phone : 800-633-5151 Population : Number of potentially involved : 354 Estimated percentage with defect : 1 % Vehicle Information : Vehicle 1 : 2020-2021 Hyundai
Accent Vehicle Type : LIGHT VEHICLES Body Style : 4-DOOR Power Train : GAS Descriptive Information : 354 model year 2020-2021 Accent vehicles produced on March 25, 2020 through July 28, 2020 by Kia Motors Mexico (“KMM”) for sale in the U.S. market. Production Dates : MAR 25, 2020 – JUL 28, 2020 VIN Range 1 : Begin : NR End : NR Not sequential Description of Defect : Description of the Defect : The front driver-side and/or passenger-side seat belt pretensioners in the subject vehicles were installed from a suspect production lot containing pyrotechnic-type pretensioners that may deploy abnormally during a crash. At the time of this filing, the cause of the abnormal deployment is unknown. Hyundai
is recalling vehicles equipped with pretensioners produced within the same production lot to conduct a detailed part return analysis. The part inspections and investigation will actively continue to determine if a specific root cause and defect trend exists. FMVSS 1 : NR FMVSS 2 : NR Description of the Safety Risk : An abnormal pyrotechnic pretensioner deployment could cause metal fragments to enter the vehicle occupant compartment, which may result in injury to vehicle occupants. Description of the Cause : Hyundai
is actively investigating root cause. Identification of Any Warning that can Occur : None. Part 573 Safety Recall Report 22V-069 Page 2 The information contained in this report was submitted pursuant to 49 CFR §573 Involved Components : Component Name 1 : S/BELT ASSY-FR P/TENSR 3PT LH/RH Component Description : Seat belt assembly w/ pretensioner for driver’s side & Passenger’ side Component Part Number : 88810J0600 Supplier Identification : Component Manufacturer Name : Samsong Address : Jungdong St, 62-30 Seongsan-gu Changwon, Gyeongnam Foreign States 51553 Country : Korea, Republic of Chronology : See Attachment A for the requested chronology of events. Description of Remedy : Description of Remedy Program : Hyundai
Motor America plans to notify owners of affected vehicles by first class mail with instructions to bring their vehicles to a Hyundai
dealer to have the seat belt pretensioner(s) replacement remedy performed. This remedy will be offered at no cost to owners for all affected vehicles, regardless of whether the affected vehicles are still covered under Hyundai
’s New Vehicle Limited Warranty. Additionally, Hyundai
will provide owners of affected vehicles reimbursement for out-of-pocket expenses incurred to obtain a remedy for the recall condition in accordance with the reimbursement plan submitted to NHTSA on February 24, 2022. How Remedy Component Differs from Recalled Component : N/A Identify How/When Recall Condition was Corrected in Production : N/A Recall Schedule : Part 573 Safety Recall Report 22V-069 Page 3 The information contained in this report was submitted pursuant to 49 CFR §573 Description of Recall Schedule : Dealers and owners will be notified in accordance with the remedy schedule of Recall 211. Planned Dealer Notification Date : FEB 25, 2022 – FEB 25, 2022 Planned Owner Notification Date : FEB 25, 2022 – FEB 25, 2022 * NR – Not Reported
**************************************************************************************************************
OMB Control No.: 2127-0004 Part 573 Safety Recall Report 22V-069 The information contained in this report was submitted pursuant to 49 CFR §573 Manufacturer Name : Hyundai
Motor America Submission Date : FEB 09, 2022 NHTSA Recall No. : 22V-069 Manufacturer Recall No. : 219 Manufacturer Information : Manufacturer Name : Hyundai
Motor America Address : 10550 Talbert Avenue Fountain Valley CA 92708 Company phone : 800-633-5151 Population : Number of potentially involved : 354 Estimated percentage with defect : 1 % Vehicle Information : Vehicle 1 : 2020-2021 Hyundai
Accent Vehicle Type : LIGHT VEHICLES Body Style : 4-DOOR Power Train : GAS Descriptive Information : 354 model year 2020-2021 Accent vehicles produced on March 25, 2020 through July 28, 2020 by Kia Motors Mexico (“KMM”) for sale in the U.S. market. Production Dates : MAR 25, 2020 – JUL 28, 2020 VIN Range 1 : Begin : NR End : NR Not sequential Description of Defect : Description of the Defect : The front driver-side and/or passenger-side seat belt pretensioners in the subject vehicles were installed from a suspect production lot containing pyrotechnic-type pretensioners that may deploy abnormally during a crash. At the time of this filing, the cause of the abnormal deployment is unknown. Hyundai is recalling vehicles equipped with pretensioners produced within the same production lot to conduct a detailed part return analysis. The part inspections and investigation will actively continue to determine if a specific root cause and defect trend exists. FMVSS 1 : NR FMVSS 2 : NR Description of the Safety Risk : An abnormal pyrotechnic pretensioner deployment could cause metal fragments to enter the vehicle occupant compartment, which may result in injury to vehicle occupants. Description of the Cause : Hyundai is actively investigating root cause. Identification of Any Warning that can Occur : None. Part 573 Safety Recall Report 22V-069 Page 2 The information contained in this report was submitted pursuant to 49 CFR §573 Involved Components : Component Name 1 : S/BELT ASSY-FR P/TENSR 3PT LH/RH Component Description : Seat belt assembly w/ pretensioner for driver’s side & Passenger’ side Component Part Number : 88810J0600 Supplier Identification : Component Manufacturer Name : Samsong Address : Jungdong St, 62-30 Seongsan-gu Changwon, Gyeongnam Foreign States 51553 Country : Korea, Republic of Chronology : See Attachment A for the requested chronology of events. Description of Remedy : Description of Remedy Program : Hyundai Motor America plans to notify owners of affected vehicles by first class mail with instructions to bring their vehicles to a Hyundai dealer to have the seat belt pretensioner(s) replaced. This remedy will be offered at no cost for all affected customers. All returned pretensioners will be collected for further analysis into root cause. How Remedy Component Differs from Recalled Component : N/A Identify How/When Recall Condition was Corrected in Production : N/A Recall Schedule : Description of Recall Schedule : Dealers and owners will be notified in accordance with the remedy schedule of Recall 211. Planned Dealer Notification Date : FEB 25, 2022 – FEB 25, 2022 Planned Owner Notification Date : FEB 25, 2022 – FEB 25, 2022 Part 573 Safety Recall Report 22V-069 Page 3 The information contained in this report was submitted pursuant to 49 CFR §573 * NR – Not Reported
**************************************************************************************************************
SEOCONTENT-END
This product presentation was made with AAWP plugin.





