October 9, 2019 NHTSA CAMPAIGN NUMBER: 19V721000
Lower Control Arm Ball Joints Can Detach
A detached ball joint can cause a loss of vehicle control, increasing the risk of a crash.
NHTSA Campaign Number: 19V721
Manufacturer Hyundai Motor America
Components SUSPENSION
Potential Number of Units Affected 744
Summary
Hyundai Motor America (Hyundai) is recalling certain 2020 Elantra vehicles. The lower control arm ball joint fasteners may have been insufficiently tightened allowing the ball joint to detach from the lower control arm.
Remedy
Hyundai will notify owners, and dealers will inspect and, as necessary, tighten the ball joint fasteners, free of charge. The recall began November 20, 2019. Owners may contact Hyundai customer service at 1-855-371-9460. Hyundai’s number for this recall is 185.
Notes
Owners may also contact the National Highway Traffic Safety Administration Vehicle Safety Hotline at 1-888-327-4236 (TTY 1-800-424-9153), or go to www.safercar.gov.
Check if your Hyundai has a Recall
| Technical Service Bulletin | GROUP RECALL | NUMBER
19-01-032H |
| DATE
OCTOBER, 2019 | MODEL(S)
Elantra (ADa) | |
| SUBJECT:
BALL JOINT FASTENER TORQUE (RECALL CAMPAIGN 185) | ||
IMPORTANT
*** Dealer Stock and Retail Vehicles ***
Dealers must perform this Recall Campaign on all affected vehicles prior to customer retail delivery and whenever an affected vehicle is in the shop for any maintenance or repair.
When a vehicle arrives at the service department, access Hyundai Motor America’s “Warranty Vehicle Information” screen via WEBDCS to identify open Campaigns.
Description: On certain 2020 model year Elantra (ADa) vehicles, the fasteners securing the lower control arm ball joints may not have been properly tightened during assembly. Loose ball joint fasteners may allow the ball joint to separate from the lower control arm, increasing the risk of a crash. This bulletin describes the procedure to confirm lower control arm ball joint fastener torque, and correct if needed.
Applicable Vehicles: Certain 2020MY Elantra (ADa) vehicles produced at Hyundai Motor Manufacturing Alabama (VIN beginning with a “5”) from September 4, 2019 through September 10, 2019.
Warranty Information:
| MODEL | OP. CODE | OPERATION | OP. TIME | CAUSAL PART # | NATURE CODE | CAUSE CODE |
| Elantra (ADa) | 91CA14R0 | Lower Control Arm Ball Joint Torque | 0.3 | 54500-F3000 | A36 | ZZ7 |
NOTE 1: Submit Claim on Campaign Claim Entry Screen
NOTE 2: If a part is found in need of replacement while performing Recall TBD and the affected part is still under warranty, submit a separate claim using the same Repair Order. If the affected part is out of warranty, submit a Prior Approval Request for goodwill consideration prior to performing the work.
Service Procedure:
- Raise the vehicle and remove the front tire/wheel assemblies.
NOTICE
The front wheels must be removed to gain access to all of the ball joint fasteners.
- Verify the bolt (A) and two nuts (B) that secure the ball joint to the lower control arm are tightened to specification.
Tightening Torque:
98.1 ~ 117.7 N.m
(10.0 ~ 12 kgf.m, 72.3 ~ 86.6 lb-ft)
Repeat the procedure for the opposite side of the vehicle.
- Reinstall the front tire/wheel assemblies onto the vehicle.
Tightening Torque:
107.9 ~ 127.5 N.m
(11.0 ~ 13.0 kgf.m, 79.6 ~ 94.0 lb-ft)
TSB #: 19-01-032H
IMPORTANT SAFETY RECALL
2020 Elantra
Lower Ball Joint Fasteners
NHTSA Recall Number: 19V-721
Hyundai Recall Number: 185
This is an important Safety Recall.
|
This notice applies to your Hyundai, VIN: XXXXXXXXXXXXXXXXX
Dear <FirstName LastName,>
This notice is sent to you in accordance with the National Traffic and Motor Vehicle Safety Act. Hyundai has decided that a defect which relates to motor vehicle safety exists in certain model year 2020 Hyundai Elantra vehicles produced between September 4, 2019 through September 10, 2019 by Hyundai Motor Manufacturing Alabama (“HMMA”) in the U.S. Our records indicate that your vehicle is affected.
What is the problem?
The fasteners securing the ball joints to the lower control arms in the subject vehicles may have been insufficiently tightened during assembly, increasing the risk of ball joint detachment from the lower control arm while driving. A detached lower ball joint while driving could increase the risk of a crash.
What will Hyundai do?
Your Hyundai dealer will inspect and tighten the ball joint fasteners, if necessary. This procedure will be performed at NO CHARGE to you.
What should you do?
Please contact your nearest Hyundai dealer to schedule the recall repair as soon as possible.
The actual time required to perform the installation will take less than one hour, however your vehicle may be needed longer, therefore we recommend scheduling a service appointment to minimize inconvenience.
If you have other questions
If you require further assistance, you may contact the Hyundai Customer Care Center at 1-855-371-9460. If you believe that the dealer or Hyundai has failed or is unable to remedy the defect within a reasonable time, you may submit a complaint to the Administrator, National Highway Traffic Safety Administration, 1200 New Jersey Avenue S.E., Washington, D.C. 20590, or call the toll free Vehicle Safety Hot Line at 1-888-327-4236 (TTY: 1-800-424-9153), or go to https://www.safercar.gov.
Thank you for your attention to this important safety matter. We apologize for any inconvenience this may have caused you.
Hyundai Motor America
Importante Retiro del Mercado por Motivos de Seguridad — Si tiene preguntas llama 1-800-633-5151 y oprima “8”
Recall 185 Dealer Best Practice
Date: October 16, 2019
Attn: Dealer Principal/General Manager/Service Manager/Parts Manager
Subject: Recall 185: 2020MY Elantra BALL JOINT FASTENER TORQUE TSB #19-01-032H (Remedy Available)
| Updates To This Document | Date |
| • Initial Communications: Recall 185: 2020MY Elantra BALL JOINT FASTENER TORQUE TSB #19-01-032H (Remedy Available) | 10/16/19 |
*** Dealer Stock and Retail Vehicles ***
Dealers must perform this Recall Campaign on all affected vehicles prior to customer retail delivery and whenever an affected vehicle is in the shop for any maintenance or repair.
Affected Vehicles
Hyundai is conducting a safety recall in the United States to inspect and, if necessary, tighten the lower ball joint attachment fasteners on certain model year 2020 Hyundai Elantra vehicles produced between September 4, 2019 through September 10, 2019 by Hyundai Motor Manufacturing Alabama (“HMMA”) in the U.S.
The affected vehicles include:
- Certain 2020MY Elantra (ADa) vehicles produced at Hyundai Motor Manufacturing Alabama (VIN beginning with a “5”) from September 4, 2019 through September 10, 2019.
Hyundai is initiating this action to ensure the safety and quality of its vehicles and the continued satisfaction of Hyundai customers.
Description
The fasteners securing the ball joints to the lower control arms in the subject vehicles may have been insufficiently tightened during assembly, increasing the risk of ball joint detachment from the lower control arm while driving. A detached lower ball joint while driving could increase the risk of a crash.
Service Action
Reservation – Always check the Vehicle Information Screen in WebDCS for open campaigns and recalls, and advise the customer on time requirements.
- Provide customer with transportation options such as an SRC, alternative vehicle, shuttle or rideshare.
Readiness – Review this announcement and the accompanying FAQs with all Service and Parts staff including
Reservationist/BDC. Also, complete all applicable training, check your reservation capacity settings (you can set separate capacities for every recall/campaign), confirm email addresses for campaign appointments, and that you have all necessary tools, campaign parts and shop equipment as needed.
- Be prepared to put customers in an SRC or alternative transportation if needed.
Reception – Always check the Vehicle Information Screen in WebDCS for open campaigns and recalls, and print a copy for technicians. Provide SRC or an alternative vehicle, as needed. If a customer has declined the campaign, note this on the repair order and request the customer’s signature next to the statement.
Repair – Always plug in the GDS before starting the repair. Make sure to complete an MPI on all vehicles and Quality Control your work.
- The front wheels must be removed to gain access to all of the ball joint fasteners.
- Submit claim on Campaign Claim Entry screen
- If a part is found in need of replacement while performing Recall 185 and the affected part is still under warranty, submit a separate claim using the same Repair Order. If the affected part is out of warranty, submit a Prior Approval Request for goodwill consideration prior to performing the work.
Return – Review all completed campaign and repairs to answer any customer questions. Also, schedule the customer’s next service
Reconnect – Follow up for customer satisfaction.
Parts
No additional parts are required to complete this recall.
Customer Notification
Hyundai will begin mailing owner notifications by early December 2019.
Thank you for your prompt attention to this important matter and continued commitment to Hyundai customers.
Hyundai Motor America
Customer FAQ
Q1: What is the issue?
A1: The fasteners securing the ball joints to the lower control arms in the subject vehicles may have been insufficiently tightened during assembly, increasing the risk of ball joint detachment from the lower control arm while driving.
Q2: What are the affected vehicles?
A2: Approximately (744) 2020 Hyundai Elantra vehicles produced between September 4, 2019 through September 10, 2019 by Hyundai Motor Manufacturing Alabama (“HMMA”) in the U.S.
Q3: What is the safety concern?
A3: Insufficiently tightened ball joint attachment fasteners could increase the risk of ball joint detachment from the lower control arm while driving. A detached lower ball joint while driving could increase the risk of a crash.
Q4: Have there been any accidents or injuries?
A4: Hyundai is not aware of any accidents or injuries related to this condition.
Q5: What will be done during the recall service at the dealer?
A5: Hyundai Motor America plans to notify owners of affected vehicles to return their vehicles to Hyundai dealers to inspect and tighten the ball joint fasteners, if necessary. The procedure will be performed at no charge. Monetary reimbursement to owners for prior related repairs will be made available in accordance with the plan submitted to the agency on May 16, 2018.
Q4: When will owners be notified?
A4: Hyundai will begin mailing owner notifications by early December 2019.
| Key Contact Information | ||
| Dealer Support | Contact Information | Description |
| Parts | [email protected] 1-800-545-4515 | Parts ordering hotline |
| Techline | 1‐800‐325‐6604 | Vehicle Technical Support for Hyundai Dealer Technicians |
| Warranty HELPREP Line | 1‐877‐446‐2922 | Warranty Claim questions for Hyundai Dealers |
| Warranty Prior Approval (PA) Center | 1‐844-371-3808 | Warranty Prior Approval (PA) Center for Hyundai Dealers |
| Xtime Technical Support | [email protected] 1‐866‐984‐6355 | Assistance with Car Care Scheduling:
• Appointment / Shop Capacity Management / Campaign Integration / Operation Codes |
| AutoLoop Technical Support | [email protected] 1-877-850-2010 | Assistance with Car Care Scheduling:
• Appointment / Shop Capacity Management / Campaign Integration / Operation Codes |
| CDK Technical Support | https://serviceconnect.support.cdk.com/ | Assistance with Car Care Scheduling:
• Appointment / Shop Capacity Management / Campaign Integration / Operation Codes |
| Customer Support | Contact Information | Description |
| Hyundai Customer Care Center (Recall / Campaign Questions) | 1‐855‐671‐3059 | Customer questions or concerns related to recall or service campaigns |
| Hyundai Recall / Campaign Website | www.hyundaiusa.com/recall | Updated information related to the specific recall or service campaign |
| Hyundai Customer Care Center (General Questions) | 1‐800‐633‐5151 | Customers general questions, non‐campaign related |
| Hyundai Roadside Assistance | 1-800-243-7766 | Hyundai Roadside Assistance |
| Key Reference Information | |
| Name | Source |
| Campaign Central | Consolidated repository of recall and service campaign dealer best practices. Located on the service tab homepage in www.HyundaiDealer.com |
| Car Care Scheduling (Xtime) – Tutorials | www.HyundaiDealer.com > Service > Dealer Resources > Documents Library > Car Care Scheduling |
| Car Care Scheduling (Xtime) – Recall Appointment Notification | 1. Log into Xtime
2. Under the menu at the top left, select ‘CONFIGURE’ 3. Under the dealership tab, click “EMAIL COMMUNICATION” 4. Slide the toggle to “ADVANCED” 5. Populate as many e-mails as desired in the “PARTS DESK EMAIL FIELD” |
| Parts – Campaign Parts Management (CPM) Procedure | As applicable; www.HyundaiDealer.com > Parts > Documents Library > Campaign Parts Management |
| Service Rental Car (SRC) Program | www.HyundaiDealer.com > Service tab > SRC Fleet Mgmt Software |
| Technical Service Bulletin (TSB) | www.HyundaiDealer.com > Service tab > Hyundai Tech Info |
| Uncompleted Campaign VIN Listing | A listing of vehicles is located on WEBDCS> SERVICE tab> select UNCOMPLETED CAMPAIGN VIN LISTING
– Dealer Stock (New, SRC, CPO, etc.) and Retailed. |
| Recall Campaign Website | www.hyundaiusa.com/recall |
| NHTSA Website | www.safercar.gov |
1 Affected Product
Vehicle
| MAKE | MODEL | YEAR |
| HYUNDAI | ELANTRA | 2020 |
8 Associated Documents
Recall Quarterly Report #1, 2019-4
RCLQRT-19V721-5407.PDF 211.135KB
Recall Quarterly Report #2, 2020-1
RCLQRT-19V721-3544.PDF 211.234KB
Owner Notification Letter(Part 577)
RCONL-19V721-6862.pdf 363.302KB
Manufacturer Notices(to Dealers,etc) – Date: October 16, 2019 Subject: Recall 185: 2020MY Elantra BALL JOINT FASTENER TORQUE TSB #19-01-032H (Remedy Available)
RCMN-19V721-3605.pdf 181.068KB
Remedy Instructions and TSB
RCRIT-19V721-4588.pdf 352.444KB
Recall Acknowledgement
RCAK-19V721-2465.pdf 244.149KB
Defect Notice 573 Report
RCLRPT-19V721-9537.PDF 212.973KB
Recall Quarterly Report #3, 2020-2
RCLQRT-19V721-6609.PDF 211.313KB
Recalls Documents
- ESSENTIAL TOOL FOR BALL JOINT SERVICE - Use the ORION MOTOR TECH Ball Joint Press Set Ball Joint Tool / Bushing Removal Tool with 4WD Adapter to effortlessly remove press fit parts including ball joints, U-joints, brake anchor pins, and more on most 2-wheel drive (2WD) and 4-wheel drive (4WD) vehicles without removing the control arm from the vehicle.
- PROFESSIONAL GRADE QUALITY AND DURABILITY - Off road weekend warriors, novices, and professional mechanics trust the ORION kit because ORION MOTOR TECH sources the highest quality components from around the world. Constructed from heavy-duty forged steel with black-oxide finish on adapters for maximum strength and longevity that resists rust and corrosion.
- UNIVERSALLY COMPATIBLE WITH A WIDE RANGE OF VEHICLES - Fit most American domestic and imported 2-wheel drive (2WD) and 4-wheel drive (4WD) cars and light pickup trucks that have press-fit type ball joints, include 4-wheel drive (4WD) adapter that allows service for 1967 thru current 1/2 and 3/4 ton 4WD vehicles having the Dana 30 or 44 front axle (found on Ford, GM, Dodge, IHC and Jeep vehicles).
- CONVENIENTLY ORGANIZED IN CUSTOM MOLDED CASE - Ball joint press / bushing/ removal tool kit is enclosed inside a heavy-duty 11” x 3” x 15” inch (27.9cm x 7.6cm x 38.1cm) plastic blow-molded carrying case with handle for easy storage, safe storage, and quick organization. Package include: 3x Receiving Tube, 1x Removal Adapter, 1x Installation Adapter, 1x Screw, 1x Install Cup Adapter, 1x Forcing-screw Press, 1x Receiving Cup, 1x Installing Cup.
- ORION MOTOR TECH - We pursue outstanding quality and professional technical support. If you are not satisfied with this product or if you have any question, please feel free to let us know.
- Premium Quality: This ball joint tool kit is made of solid carbon steel with anti-rust finish, perfect for removal/installation of press-fit parts, such as ball joints, universal joint and truck brake anchor pins.
- Easy To Use: It will help you effortlessly remove press fit parts including ball joints, U-joints, brake anchor pins without removing the control arm from the vehicle. Besides, this tool kit can also remove rusted and corroded parts. Really save your energy and time in daily life.
- Package Included: 3x Receiving Tubes, 1x Removal Adapter, 1x Installation Adapter, 1x Screw, 1x Install Cup Adapter, 1x Forcing-screw Press, 1x Receiving Cup, 1x Installing Cup.
- Wide Application: The heavy duty 4-wheel drive ball joint tool is compatible with most American domestic and imported 2-wheel drive (2WD) and 4-wheel drive (4WD) cars. It allows service for 1/2 and 3/4 ton 4WD vehicles
- Blow Storage Case: The Ball Joint Press set is packed in a heavy-duty, storage case with precision-sized compartments for every piece - great for storage and transport while lengthening the life of the tool set.
- EASY OPERATION: Use the ORION MOTOR TECH Ball Joint Press Tool Set with 4WD Adapter to effortlessly remove press-fit parts including ball joints, U-joints, brake anchor pins, and more on most 2-wheel drive (2WD) and 4-wheel drive (4WD) vehicles without removing the control arm.
- UNIVERSAL COMPATIBILITY: Fits most American domestic and imported cars and light pickup trucks with press-fit type ball joints. Includes a 4WD adapter for service on 1967 - current 1/2 and 3/4 ton 4WD vehicles with the Dana 30 or 44 front axle (found on Ford, GM, Dodge, IHC, and Jeep vehicles).
- PROFESSIONAL-GRADE DURABILITY: Constructed from heavy-duty forged steel with black-oxide finished adapters for maximum strength and longevity that resists rust and corrosion to endure years of heavy use.
- ALL-IN-ONE TOOL KIT: 3x Receiving Tubes, 1x Removal Adapter, 1x Installation Adapter, 1x Screw, 1x Install Cup Adapter, 1x Forcing-screw Press, 1x Receiving Cup, 1x Installing Cup.
- PROTECTIVE CARRYING CASE: Each component is contained in a heavy-duty plastic carrying case with a handle for safe storage and quick organization.
- Gearwrench's Ball Joint Separator is made for separating the ball joint from the spindle support arm on domestic and import front wheel drive vehicles
- Adjustable for different size ball joints
- Suitable for most cars and light trucks (not intended for use on 3/4 ton or 1 ton trucks)
- Works on ball joints from 1-1/8” to 2-1/8” and 30 to 56mm in size
- Slot is 7/8" wide by 1-1/4" Deep
- Complete Tool Set: Orion Motor Tech's master ball joint removal tool kit includes a 5 pc. front-end service tool kit and a 21 pc. ball joint tool set. It provides everything you need for removing and installing ball joints, tie rods, Pitman arms, & more
- Wide Compatibility: This ball joint servicing kit is compatible with most GM, Chevrolet, Ford, and Dodge vehicles with 2WD or 4WD setups, including Dana 28, 30, 35, 44, & 60 axles. It works on light trucks, vans, SUVs, & many domestic & imported vehicles
- Easy Operation: Our 21-piece ball joint press kit lets you service joints and anchor pins without removing control arms. The multiple adapter sizes speed up ball joint and U-joint removal on most vehicles
- Rugged Build: Built from high-strength forged steel, this suspension service kit handles the toughest jobs. With a protective black oxide coating, these ball joint tools withstand corrosion and are built for long-term garage or shop use
- Carry Case Included: The convenient ABS storage case is built to store each ball joint press tool in a custom-molded slot. Stay organized during every job and avoid delays from misplaced tools or missing parts
This product presentation was made with AAWP plugin.





